% % %

Four Myths About High-Capacity Enterprise Hard Drives — Debunked With Real Numbers

Myth #1: “All 22TB drives use SMR.” The WD Ultrastar DC HC570 uses CMR (Conventional Magnetic Recording) with energy-assisted PMR (ePMR) and OptiNAND technology — not SMR. Sequential and random write performance is consistent, with no write-amplification penalty and no performance collapse when the drive’s internal CMR-to-SMR translation layer fills up. For ZFS, Ceph, and any array that does mixed read-write workloads, CMR is non-negotiable. The HC570 delivers it at 22TB.

Myth #2: “Helium-filled drives leak and fail after 3 years.” WD’s HelioSeal technology has been in production since 2013 (HGST Ultrastar He6). Field data from hyperscale customers shows annualized failure rates (AFR) on helium-sealed 22TB drives at 0.35% — lower than the 0.73% AFR on equivalent-capacity air-filled drives. The helium molecules are larger than the atomic gaps in the hermetic seal; leakage rates are measured in decades, not years.

Myth #3: “22TB drives are too slow for anything but cold storage.” ~에 265 MB/s sustained transfer and 550 TB/year workload rating, the HC570 handles warm-tier storage, backup repositories, media archives, and file servers without becoming a bottleneck. Pair it with NVMe SSDs as a cache tier for performance-critical workloads. The IOPS gap between HDDs and SSDs is real, but the capacity gap is larger — and for 80% of enterprise data, capacity per dollar matters more than IOPS per dollar.

Myth #4: “You cannot mix drive capacities in a RAID array.” You can mix 22TB, 20결핵, and 18TB drives in the same RAID array — but all drives will be limited to the smallest capacity in the array. Replacing 18TB drives with 22TB drives one at a time within a RAID group wastes the incremental capacity until the last 18TB drive is replaced. The correct migration path: create a new RAID group with 22TB drives, migrate data, decommission the 18TB group. Or use non-RAID architectures (Ceph, ZFS) where mixed drive sizes are handled natively at the pool level.

기술 사양

매개변수	사양
용량	22결핵 (also: 18결핵, 20TB in DC HC5xx series)
폼 팩터	3.5-인치 LFF
인터페이스	SAS 12Gb/s
회전 속도	7,200 RPM
Recording Technology	CMR (ePMR + OptiNAND), energy-assisted perpendicular magnetic recording
은닉처	512 MB buffer + OptiNAND (embedded UFS NAND for metadata acceleration)
Sustained Transfer Rate	까지 265 MB/s
Average Latency	4.16 MS
MTBF	2,500,000 시간
AFR (Annualized Failure Rate)	0.35%
Workload Rate Limit	550 TB/year
Unrecoverable Bit Error Rate	1 sector per 10^15 bits read
힘 (Idle / 운영 중 / Peak Spin-Up)	5.6승 / 7.4승 / 25승 (spin-up)
Sealing	HelioSeal (hermetically sealed, helium-filled, 7세대)
섹터 크기	512e or 4Kn (selectable at format)
충격 (운영 중 / Non-Operating)	50G / 250G (2 MS)
Rotational Vibration	RVFF (Rotational Vibration Feed Forward) sensor array
Physical	147.0 엑스 101.6 엑스 26.1 mm, 690g
온도	5°C to 60°C
보증	5-year limited (manufacturer)

OptiNAND — What It Actually Does

OptiNAND embeds an iNAND UFS (Universal Flash Storage) chip on the HDD PCB. It stores metadata — write cache state, servo positioning data, and defect maps — that was previously stored on a portion of the spinning platters. By moving metadata to persistent flash, the drive recovers roughly 2-3% of usable capacity that was consumed by metadata overhead on the platters. More importantly, it eliminates the need for a DRAM-based write cache to be flushed to platters on unexpected power loss — the OptiNAND flash retains write cache state across power cycles without consuming drive platter space.

Compatible Platforms

Compatible with all Dell PowerEdge servers with 3.5-inch SAS backplanes, xFusion FusionServer V7, 레노버 씽크시스템, and any SAS 12Gb/s platform. Full compatibility with PERC H730/H740/H750/H755/H965i, LSI/Broadcom 93xx/94xx/96xx SAS HBAs.